DigiMash All-Grain Electric Brewing System - 35L/9.25G

The DigiMash system represents the best value in electric all-grain brewing you'll find. With a 9-gallon DigiBoil electric kettle and the DigiMash stainless steel mashing accessory pack included, this is by far the most affordable way to get into electric all-grain brewing.  It may not have all the bells and whistles of the BrewZilla, but it does have everything you need to mash and boil all in one unit. Setting up and using the DigiMash couldn't be easier. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperature on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil.

If you're deciding between the DigiMash and the BrewZilla, there are a couple of key differences worth noting. One of our favorite features of the BrewZilla is the programmable mash steps and delayed start, which the DigiMash does not have. You can still step mash by simply raising the temperature manually on the controller, but the automatic steps are a convenient feature if you want to set it and forget it.

This model comes with the 35L DigiBoil, which has two built-in heating elements that run off a 220V or 110V plug. One element is 1900w and the other is 500w for a combined 2400 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from mash temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s).

If you have access to 220V power, this is definitely the unit we recommend. Although 110V power is enough to get up to boil, 220V will get you there faster and provide a much more vigorous boil.

Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach fittings with 1/2" FPT, such as our female threaded quick disconnect.

DigiBoil Features:

• 304 stainless steel construction
• 9 gallon total capacity
• Digital temperature control
• 110V or 220V / 15A power 
• NEMA 6-30R plug (5 ft. cord)
• Dual heating element control (1000w and 500w)
• Heating elements are concealed for easy cleaning
• 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2")
• Stamped-in volume markers (gallons & liters)
• Stainless lid
• Temperature reads in °F or °C
  • With elements turned off, hold both +/- buttons to switch between °F or °C
• Recommended max. grain bill - 18 lbs
• Recommended min. grain bill - 8 lbs
• External Dimensions: 29" H x 15" W (including handles)
• Internal Dimensions: 19.5" H x 11.75" W

DigiMash Upgrade Includes:

• False bottom
• Malt pipe
• Wire support 
• Malt pipe handle
• Malt pipe bottom screen

• Place the false bottom inside the kettle
• Install the wire support in the channel located at the top of the kettle
• Place the mesh screen inside the malt pipe and attach the handle
• Lower the malt pipe into the kettle so it rests on the wire support
• Fill with strike water and heat to desired temperature
• Add grain, stir until well mixed, and adjust controller to target mash temperature
• When your mash is complete, use the handle to lift out malt pipe and rotate 90° so the malt pipe feet sit on the wire support
• Allow the wort to drain into the kettle and sparge the grain with warm water (165-175°F)
• When you're done collecting wort, remove the malt pipe and proceed to boil

Please note: only the 500-watt element should be used to increase mash temperatures when the Malt Pipe is in place. Using the higher watt element(s) with the Malt Pipe inserted may cause scorching of the grain.